Categories
Info Measurement

Shower vs Bath Water Usage

Shower vs Bath Water Usage: The bathroom constitutes the bigger half of all domestic house water usage. With so much water being used, there are easy opportunities to save both water and money.

Shower vs Bath Water Usage: The debate

The most important bathroom activity is bathing. There is a big debate whether bathing in a bath uses more water than taking a shower.

Shower vs Bath Water Usage: The debate

How much Water does a Shower use

The biggest factors here are flow rate and length (total time) of a shower.

An ordinary electrically heated shower puts out four litres (1 gallon) per minute. But the next statistic will suggest it is more like double that.

Home Water Works says that in most homes, showers are the third-largest user of water after toilets and clothes washers. The average American shower water usage is 17.2 gallons with the average shower length being 8.2 minutes. The average flow rate is 2.1 gallons per minute.

Suggested Read -> How to clean a showerhead with vinegar

What is the average shower time

Men shower at an average of 7 minutes while women shower at an average shower length of 9 minutes.

An older person of say age bracket of 50 years and above showers for 4 to 5 minutes while teenagers can shower up to 25 minutes.

How much Water does a Shower use

With such diverse variation, it would be best to rather use the average statistic quoted by Home Water Works : 8.2 minutes.

How much Water does a Bath use

The biggest factor here is the size of a bath.

A bath uses between 50 to 150 litres (14 to 40 gallons) of water per fill, depending on the water level.

A bath filled about a third of the way up (which takes the water level over your belly button when you lie down) requires around 75 litres (20 gallons).

What uses more water, a Bath, or a Shower

Lets take the lowest then the average and finally the highest of all stats on both a bath and a shower and make a broad comparison.

Lowest Shower vs Bath Water Usage

Bath = 50 litres (14 gallons)

Shower = 4 liter (1 gallon) per minute (low flow rate shower head and setting) for 4 minutes (old person) = 16 liter (4.2 gallons)

So in this case the shower uses significant less water than a bath, at just about one third. (16 vs 50 | 4.2 vs 14)

What uses more water, a Bath, or a Shower

Average Shower vs Bath Water Usage

Bath = 75 litres (20 gallons)

Shower = 5.9 liter (1.55 gallon) per minute (average between highest and lowest) for 8.2 minutes (average American) = 48 liter (12.7 gallons)

In this instance the shower uses less than the bath, at approximately 2 thirds. (48 vs 75 | 12.7 vs 20)

Highest Shower vs Bath Water Usage

Bath = 150 litres (40 gallons)

Shower = 8 liter (2.1 gallon) per minute (high flow rate shower head and setting) for 25 minutes (teenager ) = 199 liter (52.5 gallons)

In this instance the shower uses less than the bath, at approximately 3 quarters. (150 vs 199 | 40 vs 52.5)

A very conclusive answer on the debate

In all 3 cases (lowest, average and highest) clearly the shower uses less water than the bath.

Still your unique home situation may be different. You might have a very small bath or a huge luxury bath (like the royalty of the Roman empire). This will factor the calculations and results quite differently.

As already mentioned with a shower the two main factors is flow rate and total shower time. So you might have a very high flow shower head (ex. Original HIGH FLOW SHOWER HEAD – 10.5 GPM – Water Blaster Brand) and very high pressure in your water supply. I have even seen people completely removing the shower head and run the shower without it, and even turn the taps fully open. So cases like this might also tip the scales.

Categories
DIY Info

Board behind Tile in Shower Comparison

Backer Boards Comparison : I’m going to break down by category and cover the finer points of each type of Board behind Tile in Shower.

Board behind Tile in Shower – Sheetrock/Greenboard

Board behind Tile in Shower - Sheetrock/Greenboard

Sheetrock in a wet area is a primary no-no. It generally works excellent for a kitchen backs plash or fire however as a shower tile backer board, it’s a horrific concept and in opposition to code. This additionally is going for moisture resistant drywall also called green board. It’s my expertise that inexperienced board isn’t authorized for residential moist areas anymore.

If sheetrock (drywall) receives wet it expands and swells and could break any tile which you’ve set up on it. There are better alternatives.

Glass Mat Gypsum Wall Board

Glass Mat Gypsum Wall Board

The most popular product on this category is Densshield tile backer board [edit: apparently USG has entered this space also]. This product has taken the area of green board. it’s miles made of moisture resistant gypsum but it also has a water-resistant coating on its face. Like sheetrock, it’s smooth to install and really least expensive. because of these items, it’s far the new favorite of home builders anywhere. in which they used to use inexperienced board lower back inside the 1980’s they now use this new gypsum hybrid.

In tract homes and new production, it’s normally set up by the sheetrock group. generally, the sheetrock group (and generally the tile installers) don’t recognise how to properly water resistant the seams, screw holes, and edges. however it’s reasonably-priced and lasts lengthy sufficient which is song to most tract home builder’s ears.

Board behind Tile in Shower – Fiber cement board

Board behind Tile in Shower - Fiber cement board

Fiber cement board and cement board are carefully associated. You’ve in all likelihood heard of Hardiebacker tile backer board. Fiberock is another famous product in this class. It’s a kind of gray/beige coloured board and is to be had at any hardware box keep.

The tile backer forums that have already been mentioned are pretty smooth to reduce via scoring and snapping. however Hardiebacker and its competition aren’t nearly as smooth. It’s an awful lot stiffer and tougher. reducing it in 1/2 is plenty less complicated than slicing a 1-inch strip off the brink. you could use a talent saw or handheld grinder with a diamond blade to cut it but it’s will get dirt everywhere. including your lungs, if you don’t wear a masks. a few have observed that Hardiebacker shears paintings nicely and don’t create too much dirt however the drawback is that the brink isn’t constantly a smooth cut.

For installing make certain to apply the proper screws (or galvanized roofing nails) whilst putting in. I opt for screws due to the fact they don’t bang at the wall and reason cracking within the sheetrock in the relaxation of the room. The seams have to be taped with alkaline resistant mesh tape and thinset.

But when it comes to getting moist those fiber cement Board behind Tile in Shower maintain up properly. they’ll absorb water however will dry out without losing their form. because they will absorb moisture there must usually be some sort of a moisture barrier whilst the use of these tile backer forums in a shower or different moist region. either a vapor-kind barrier behind the board or a waterproofing membrane on the front. this could take the shape of a sheet membrane or a paint-on liquid.

Board behind Tile in Shower – Cement Board

Board behind Tile in Shower - Cement Board

Popular Cement board brands are Durock, Wonderboard, and Permabase. just like the fiber cement boards, these may be tough to cut. the issue comes now not so much from the stiffness however the edges that disintegrate. It does take some getting used to. and they’re heavy. And difficult to maintain on the wall even as you begin your screws.

Cement forums have advanced over the previous couple of years. the rims don’t crumble as bad as they used to. Permabase is the one that I opt for and i can typically force screws into the very facet with out it breaking off. also, the water absorption is pretty low. you continue to need to water-resistant them just like the fiber cement forums above. And use the same screws and mesh tape.

Foam Tile Backer Board

Foam Tile

Wedi board is probably the most famous if, for no other purpose, that it’s been out the longest. Kerdi Board is any other choice with a decently lengthy history and constant customer base. greater these days, USG Durock foam board, Laticrete Hydroban Board, and Johns Manville GoBoard have all come available on the market.

There are some huge blessings to those panels for showers: they’re light-weight and don’t harm the partitions as you carry them into the residence and upstairs. they’re simply smooth to cut and the board itself is water-proof. No want for extra waterproofing. some forums will need additional framing blocks at the seams. Wedi Board behind Tile in Shower seems to be stiffer than most.

the primary drawback is the cost and maybe availability. the froth board itself is normally three instances the value of cement board. you then have to buy the urethane sealant which you use in among the joints of every panel (or banding for merchandise like Kerdi-board). And the immaculate screws and unique washers. All that stuff adds up – and rapid.

Backer Board Wikipedia

Categories
DIY How To

How to clean a showerhead with vinegar

Is your shower head not performing like it used to? You may wonder how to clean your shower head. Over time mineral deposits can build up which can cause the nozzles to squirt water in all directions or clog up completely, leaving you with poor water pressure or low flow. So how to clean a showerhead with vinegar? In this article we will discuss how long to soak shower head in vinegar and how to clean your showerhead with vinegar and baking soda.

how to clean your shower head

 

 

How to clean a showerhead with vinegar?

How to clean a showerhead with vinegar

Removable Showerheads

  1. Remove your showerhead by turning it counterclockwise until it comes off the wall pipe. If you are unable to unscrew it by hand, loosen it with an adjustable wrench, but first wrap the fixture with a rag to prevent scratching the finish.
  2. Place your showerhead in a large pot. Add enough distilled white vinegar to completely submerge the fixture and allow it to float in the liquid. How long to soak shower head in vinegar?
  3. Allow your showerhead to soak in the vinegar. The acid in the vinegar should penetrate and dissolve any mineral deposits clogging up the spray holes.
  4. Remove the showerhead from the vinegar the following morning. Clean off any loosened mineral scale with an old toothbrush or scrub brush. Poke the spray holes with a toothpick or a very thin wire to clean out any remaining gunk. Rinse the fixture thoroughly under running tap water.
  5. Reinstall your showerhead. Apply fresh plumbing tape to the threads of the wall pipe, wrapping it counterclockwise four or five times. Screw your showerhead back onto the pipe.
  6. Turn on the cold tap water and run it through your showerhead for a few minutes. This should blast out any remaining mineral deposits and vinegar residue. Check for leaks and tighten your showerhead, if necessary.

How to clean a showerhead with vinegar - Removable Showerheads

Fixed Showerheads

  1. Pour distilled white vinegar into a sturdy plastic baggie large enough to completely submerge your showerhead. Wrap a strong rubber band around the baggie to keep it securely attached to your wall pipe. How long to soak shower head in vinegar?
  2. Allow the fixture to soak in the vinegar. Remove the baggie and run hot tap water through the showerhead for several minutes to remove the loosened mineral deposits and vinegar.
  3. Scrub your showerhead with an old toothbrush or a scrub brush to remove stubborn mineral build-up. Run cold water through your fixture to rinse out the gunk. Keep scrubbing and rinsing until your showerhead is thoroughly cleaned.

how to clean a showerhead with vinegar - Fixed Showerheads

how to clean a shower head - Fixed Showerheads

 

 

How long to soak shower head in vinegar?

You should let the shower head soak for at least an hour, but preferably over night to let the acid in the vinegar do its job, and dissolve the hard water build up.

How long to soak shower head in vinegar

The more soiled the showerhead is, the longer you will have to leave it in the vinegar.

  • If you are in a hurry, and if the showerhead is made from metal, you can place the pot on the stove and simmer the vinegar for 15 minutes.
  • If the showerhead is made from brass, or has a gold or nickel finish, take it out after 30 minutes. You can always give it another vinegar bath once you have rinsed it off.

 

 

How to clean your showerhead with vinegar and baking soda

If you have a fixed shower head that you can’t remove for cleaning, you can still use vinegar to remove the hard water deposits from the sprayer. To clean a fixed shower nozzle, you’ll need a plastic bag, rubber band, vinegar, and baking soda.

how to clean your showerhead with vinegar and baking soda

Make sure that the plastic bag is free of holes and is one that can support the weight of the vinegar for an extended period. Pour enough vinegar into the bag to completely cover the shower head. Pour about 1/3 cup baking soda for every cup of white vinegar that you pour into the bag.

Raise the bag up to the shower head and submerge the shower head completely. Tie off the top of the bag using the rubber band, twist tie, or zip tie, or an elastic band. You want to make sure to secure the bag tightly so that it stays in place when you remove your hands.

Allow the bag to stay on the shower head for at least an hour. The longer you leave the showerhead immersed in the vinegar, the cleaner it will get. Remove the bag and run the shower with hot water for several minutes until it no longer smells like vinegar.

Wikipedia

Showerheads often spray unevenly because their tiny holes have gotten plugged with mineral deposits. In order for water to flow freely, you need to remove these deposits. To do that, you may want to soak the showerhead in vinegar. And that may mean removing the showerhead from the shower arm.

Over time, mineral deposits and other gunk can clog spray holes, robbing you of a pleasant shower and increasing the amount of time it takes to remove soap and shampoo due to lackluster pressure.

Bacteria on dirty shower heads could cause sickness, especially in weak immune systems: study. … An analysis of 50 showerheads from nine U.S. cities found that about 30 percent harbored high levels of Mycobacterium avium — a group of bacteria that can cause lung infections when inhaled or swallowed.

So we hope you enjoyed our article giving you the absolute best tips on how to clean your shower head with vinegar and baking soda optionally.

Disassemble Mira Shower Head – How To

Shower head having removable spray former to permit cleaning

Shower head with nozzles having self-cleaning tips

High Efficiency Water Pick Cleaning Apparatus and Showerhead

Categories
DIY How To Info

Water not coming out of shower head properly

Why is water not coming out of shower head properly? – You step into the shower and open the shower valve/s and you expect steams of water to shower all over you. Yet no water comes out of the shower head. Bummer hey ?!

Shower head blocked

Blocked pipes

Diverter Valve Malfunction

So what causes water not coming out of shower head properly?

water not coming out of shower head properly

You need good water pressure as well as good water flow to have a nice shower.

 

 

Shower head is blocked.

You need to clean / unblock your shower head

You need:

1) a zippered bag or sandwich bag, heck you could even use a produce bag.

2) an elastic band, tie wrap or hair elastic (I’m all about options)

3) white vinegar (no options here, just plain white vinegar)

clean / unblock your shower head

Water not coming out of shower head properly: Fill your bag about half way with vinegar and fasten the bag to the shower head.  Do this by enclosing the mouth of the bag over the shower head and fastening it tightly in place with the tie.  Ensure the shower head is fully immersed in the vinegar, it needs to be in order for this to work.  Let’s say yours is on a hose (like mine), then I’d suggest taking the hose down and letting it sit in the tub.  Let this sit for 12 hours, or 24 if the shower head is really crusty and you have an alternative shower you can use.

When done, simply remove the bag (careful not to get any vinegar on your or worse, in your eye), and dump down the drain.  Yes, it will smell for a few minutes but shortly thereafter you’ll notice no smell.  If you want to be super sassy, throw some baking soda down your drain before you dump out the vinegar and you’ve now also cleaned our your drain in the process (go you!).  Let the shower head run hot water for a minute before getting in, you’ll marvel at your handiwork; it will run like new!

If you are having stubborn stain issues, you can soak the shower head even longer to see if it will blast away.  If you wish, you can use some baking soda and rub that in to the small nozzles with a cleaning toothbrush which will help break down any additional limescale and remove the discoloration.  Rinse it clean and you should notice a difference.  Keep in mind that brown discoloration is ugly (I believe this has to do with iron content in water), but is not harming the functionality of the shower head. Green and white ‘crust’ is what you really need to work on, calcium and limescale are the culprits in clogging your shower head.

 

 

Water not coming out of shower head properly – Blocked pipes

Water not coming out of shower head properly - Blocked pipes

Before using any of these repair methods, plumbers will check to make sure there isn’t a faulty fixture or blocked faucet aerator causing the trouble. After ascertaining that a clogged water supply pipes is the culprit, they can use these methods:

  1. Pipe removal and cleaning: The plumbers locate the pipes with the clogs and detach them from the rest of the plumbing. They then use powerful cleaners to thoroughly remove the deposits from the inside, then restore the pipe to place and test the water flow.
  2. Pipe replacement: This is the common solution for when pipe clogging has become extreme and/or the pipe is made from corroded older material. Plumbers will track down the pipes that are causing the trouble and remove them and put in new pipes, usually made of more corrosive-resistant material (copper, PEX, CPVC) and with a larger diameter to reduce water pressure.
  3. Air pressure: This is essentially the “plunger” for a water supply pipe. Plumbers attach an air hose line to the faucet affected by a local clog. They blast air pressure into the faucet, then run the water to watch for dislodged corrosion, calcite, etc.

 

 

Diverter Valve Malfunction

Diverter Valve Malfunction

Water not coming out of shower head properly – If you have a bathtub with a shower installed in there as well, then you also must have a diverter valve. This valve is located at the shower faucet and it changes the flow of water. So, when you pull the diverter valve to one side, the water will only flow through the faucet or the shower head, depending on the side.

Anyhow, the problem might be located there as well. Simply speaking, if the diverter valve is old or just malfunctioning, water will not come out of your shower head properly.

This can happen due to the fact that diverter valve is regulating the flow of water and if it doesn’t work properly, neither will your shower head.

Categories
DIY How To

How to unclog a shower drain with standing water

How to unclog a shower drain with standing water – Standing water pools can attract insects, making your life difficult. Standing water makes clearing the clog more challenging, but you can often correct the clog yourself. What a drag! – Wow! – Can you think of a more gross way to spend your time than unblocking a drain. Luckily for you, here at Shower Eden we have solutions.

Use Plunger

Remove Clog by Hand

Home Remedy – The Bomb

Drain Unblocker Aerosol

How to unclog a shower drain with standing water – Don’t use bleach.

Bleach will kill al the good bacteria. Enzyme-based drain cleaners will work better. Bleach will also weaken your pipes and shorten their life time.

How to unclog a shower drain - Enzyme-based drain cleaner
Enzyme-based drain cleaner

 

 

Procedure One.

Put on a pair of rubber gloves and clear the blockage from the drain. This means all visible debris, or debris you can feel under the standing water. This might by luck be enough to get the water draining, slowly at least.

Next use a plunger. Place the plunger over the shower drain and plunge in and out. Plunging actually works best in standing water (water above the plunger to help it seal). After vigorously plunging, you should see some debris or gunk (yucky stuff anyway) floating around in the standing water.

How to unclog a shower drain with standing water - use plunger
Plunger

Plunging should almost definitely get the shower drain unblocked at least to a point where the water flows out even just a little bit. So wait for the standing water to drain out.

 

 

Remove Drain Cover and remove Clog by Hand if applicable.

How to unclog a shower drain with standing water by hand.

  • First you need to remove the drain cover.
  • Sometimes there is a screw in the middle that you have to take out.
  • Other times you can pry the drain cover off using a screwdriver.
  • Look inside the drain and locate the clog.
  • Use a flashlight, if necessary.
  • If the clog is within reach, pull it out with your fingers.

There might not be anything in reach to pull out. Then just continue with the rest of the steps in this article.

How to unclog a shower drain with standing water by hand
Remove Drain Cover.

 

 

How to unclog a shower drain with standing water – Now the BOMB!

Ingredients:

  • Baking Soda
  • 1 Cup of Vinegar
  • Hot Water
How to Unclog a Drain with Baking Soda and Vinegar
Baking soda + Vinegar = Clean drain

Procedure:

  1. Pour a cup of water down your drain
  2. Put the half cup of baking soda down the drain
  3. Mix in the vinegar with your second prepared cup of water
  4. Pour in the vinegar/water mixture down the drain with the added baking soda – Things will begin to bubble/fizz, this is good, it means things are working!
  5. Cover the drain to allow the chemistry to take place between the vinegar and the baking soda
  6. Set the timer for 10 minutes to allow the formula to take care of your clog
  7. Pour another cup of boiled water down your drain to flush out the remaining clog

If you have tried all of the above and the shower drain is still blocked, then:

 

 

How to unclog a shower drain –  Drain Unblocker Aerosol.

Drain Unblocker Aerosol
Drain Unblocker Aerosol
How to unclog a shower drain -  Drain Unblocker Aerosol
Drain Unblocker Aerosol for Blocked shower drains.

Drain unblocker aerosol id designed to powerfully inject compressed air into your shower drain and thus pressuring loose the blockage and effectively blowing it out. It clears clogged or sluggish drains in seconds without the use of harsh chemicals, acids, or lye.

Directions for using Drain Unblocker Aerosol for Blocked shower drains.

  1. Fill shower  base with enough water to submerge can’s cap or use directly in standing water.
  2. Block overflow with damp rag or sponge and hold firmly.
  3. Place can’s cap over drain opening and press firmly for one second. Repeat if necessary.

Slow-Moving Shower Drains
1. Place stopper in drain.
2. Fill shower drain with 6-7” of water, remove stopper.
3. Block overflow with damp rag or sponge and hold firmly.
4. Place can’s cap over drain opening and press firmly for one second. Repeat if necessary.

If all of the above fails to unblock your shower drain then call a qualified plumber. A tip : Steal with your eyes : Carefully watch what the plumber does to alleviate the problem.

Categories
Disassemble DIY How To

How to remove Delta shower handle

How to remove Delta shower handle?You might want to do maintenance or fault finding on your Delta shower valve. So you want do disassemble the shower valve. The first part you notice is the handle. How can you take of the handle. Some handles don’t even have visible screws. No problem. Here in this article I will show you various kinds of Delta shower handles and how to remove them.

With Exposed Screws

With Plug Buttons

With Setscrews

With Threaded Bonnets

How to remove Delta shower handle – Handle screws behind face plate.

How to remove Delta shower handle - Handle screws behind face plate

Some times the screws securing the handle is behind the face plate. Thus you can not see the handle screws.

In this case you have to unscrew the the face plate first. The handle plus the face plate can the be pulled off.

The you see the handle screws behind the face plate which you may the unscrew to take the handle off.

How to remove Delta shower handle

Handle screws behind face plate

Handle screws behind face plate 2

 

 

 

With Exposed Screws

With Exposed Screws

Unscrew the handle screw and remove the handle, bonnet and sleeve from the valve stem.

Unscrew the two screws from the face plate. Remove the escutcheon and the face plate.

If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapt or from the valve.

 

 

How to remove Delta shower handle – with Plug Buttons

Delta shower handle with Plug Buttons

 

Using a flat-blade screwdriver, gently pry the plug button from the front of the valve trim.
Unscrew the screw and remove the handle and adapter from the valve stem.
If applicable, rotate the cover counterclockwise to remove.
Slide the sleeve off the valve.
Unscrew the two screws and remove the face plate.
If applicable, use a flat-blade screwdriver to remove the pin from the adapter.
Unscrew and remove the adapter from the valve.

 

 

Trim with Setscrews

Trim with Setscrews

Loosen the setscrew and slide the handle and adapter off the valve.
Slide the sleeve off the valve.
Unscrew the two screws and remove the face plate.
If applicable, use a flat-blade screwdriver to remove the pin from the adapter.
Unscrew and remove the adapter from the valve.

How to remove Delta shower handle - Delta Faucet Ara 17

How to remove Delta shower handle - Delta Faucet Ashlyn 17

How to remove Delta shower handle - Delta Faucet Lahara 17

Delta Faucet Vero 17 Series Dual-Function Shower Handle Valve

 

 

How to remove Delta shower handle – with Threaded Bonnets

How to remove Delta shower handle – with Threaded Bonnets

  • Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve.
  • If applicable, remove the pivot ring. Remove the face plate from the valve.
  • Using a Phillips screwdriver, unscrew the two screws and remove the retainer.
  • If no screws are present, unscrew and remove the retainer.

How to remove Delta shower handle

How to remove Delta shower handle

Delta Foundations BT13010 Monitor 13 Series Valve

Delta T13020-SS Monitor 13 Series Valve

Categories
Disassemble DIY How To

How to remove Kohler shower handle

How to remove Kohler shower handle? Before you can do any sort of fault finding on a Kohler shower valve, you will need to remove the shower valve handle. The handle is the first part to take off. But some handles don’t even have visible screws. No problem. Here in this article I will show you various kinds of Kohler shower handles and how to remove them.

With Plug Buttons

With Setscrews

With Threaded Bonnets

With Center Cap

How to remove Kohler shower handle – with Exposed Screws

How to remove Kohler shower handle - with Exposed Screws

  • Using a Phillips screwdriver, unscrew the screw and remove the handle, bonnet and sleeve from the valve stem.
  • Using a Phillips screwdriver, unscrew the two screws from the face plate. Remove the escutcheon and the face plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapt or from the valve.

 

 

Kohler shower handle – with Plug Buttons

Kohler shower handle - with Plug Buttons

  • Using a flat-blade screwdriver, gently pry the plug button from the front of the valve trim.
  • Using a Phillips screwdriver, unscrew the screw and remove the handle and adapter from the valve stem.
  • If applicable, rotate the cover counterclockwise to remove.
  • Slide the sleeve off the valve.
  • Using a Phillips screwdriver, unscrew the two screws and remove the face plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

Kohler shower handle - with Plug Buttons

  • Using a flat-blade screwdriver, gently pry the plug button from the front of the valve trim.
  • Using a Phillips screwdriver, unscrew the screw and remove the handle and adapter from the valve stem.
  • Using a 3/32” hex wrench, loosen the setscrew and slide the bonnet off the valve.
  • Turn the sleeve counterclockwise and remove it from the valve.
  • Unscrew the collar. You may need a special tool (K-87448) to unscrew the collar. Remove the face plate and the collar.
  • Using a Phillips screwdriver, unscrew the two screws and remove the seal plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

 

 

 

Trim with Setscrews

Trim with Setscrews

  • Using a 3/32” hex wrench, loosen the two setscrews. You may need to rotate the sleeve to access both setscrews. Slide the handle and sleeve off the valve.
  • Using a Phillips screwdriver, unscrew the screw and remove the adapter from the valve stem.
  • Unscrew the collar. You may need a special tool (K-87448) to unscrew the collar. Remove the face plate and the collar.
  • Using a Phillips screwdriver, unscrew the two screws and remove the seal plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

Trim with Setscrews

  • Using a 3/32” hex wrench, loosen the setscrew and slide the handle off the valve trim.
  • Using a Phillips screwdriver, unscrew the screw and remove the bonnet and sleeve from the valve stem.
  • Using a Phillips screwdriver, unscrew the two screws from the face plate. Remove the washer and the face plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

How to remove Kohler shower handle - Trim with Setscrews

  • Using a 3/32” hex wrench, loosen the setscrew and slide the handle and adapter off the valve.
  • Slide the sleeve off the valve.
  • Using a Phillips screwdriver, unscrew the two screws and remove the face plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

How to remove Kohler shower handle - Trim with Setscrews

  • Using a 3/32” hex wrench, loosen the two setscrews. Slide the handle and bonnet off the valve.
  • Gently pry the cover plate from the escutcheon to expose the two screws.
  • Using a Phillips screwdriver, unscrew the screw and remove the adapter from the valve stem.
  • Using a Phillips screwdriver, unscrew the two screws and remove the escutcheon.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

 

 

How to remove Kohler shower handle – with Threaded Bonnets

How to remove Kohler shower handle - with Threaded Bonnets

  • Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve stem.
  • Remove the face plate from the seal plate.
  • Using a Phillips screwdriver, unscrew the two screws and remove the seal plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

With Threaded Bonnets

  • Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve.
  • If applicable, remove the pivot ring. Remove the face plate from the valve.
  • Using a Phillips screwdriver, unscrew the two screws and remove the retainer.
  • If no screws are present, unscrew and remove the retainer.

With Threaded Bonnets

  • Firmly grasp the handle. Turn the bonnet counterclockwise and remove the handle and bonnet from the valve stem.
  • Using a Phillips screwdriver, unscrew the two screws and remove the handle sleeve, shroud, and face plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.

 

 

How to remove Kohler shower handle – 

with Center Cap

How to remove Kohler shower handle - with Center Cap

  • While holding the handle arm, unscrew the end cap. Remove the end cap, washer, and short sleeve.
  • Slide the handle arm from the bonnet. Ensure the O-ring and long sleeve are still in place.
  • Slide the center cap from the bonnet.
  • Using a 3/32” hex wrench, unscrew the screw from the bonnet.
  • Slide the bonnet and sleeve from the valve stem.
  • Using a Phillips screwdriver, unscrew the two screws from the escutcheon assembly. Remove the escutcheon assembly and the face plate.
  • If applicable, use a flat-blade screwdriver to remove the pin from the adapter. Unscrew and remove the adapter from the valve.
Categories
Info Measurement

Height of Shower Valve?

You might be remodeling or you might be installing a new shower. So you are wondering: Height of Shower Valve? Shower valve/s placed to high or low will prove to be a huge ergonomic burden. Thus it is imperative to read this guide before making the call.

ADA (Americans with Disabilities Act)

Human length variation

Also consider with children using the shower, a valve placed too high, plus the playful nature of a child, will equal a head bumped on the valve. As some valves have relative sharp angled control knobs, there will be an extra shower … The tears of a crying child.

Well if you are the owner of the shower, I suppose you can choose any height that may please you. But…

If you are considering other people who might also use the shower, you might want to use the ADA (Americans with Disabilities Act) Shower Valve Measurements Requirements.

Height of Shower Valve

 

 

Height of Shower Valve? – ADA Shower Valve Measurements Requirements.

If you are considering other people who might also use the shower, you might want to use the ADA (Americans with Disabilities Act) Shower Valve Measurements Requirements.

Height Above Floor.

Shower controls area minimum height above the floor is 38 inches above the floor. The maximum height above the floor is 48 inches.

Height of Shower Valve

 

 

Height of Shower Valve? – Human length variation

The tallest member of the household should not have to bend to take hold of the shower valve/s.

An older member might have difficulty standing in the shower because of weak feet or legs. This member might want to sit on some chair inside the shower. Thus he/she should still be able to reach the shower valve/s.

Also consider looking up your local building codes, as not all towns and cities have laws regulating the installation of shower valves.

If building codes don’t regulate the location of your valve, place it in a spot that is easy for everyone to access.

A good rule of thumb: for Height of Shower Valve:

Install the valve/s between 36 and 48 inches above the shower floor.

A height of 28 inches, or 2 feet 4 inches, is standard for valves in bathtub shower units.

 

Categories
Disassemble DIY How To

Disassemble Mira Shower Head – How To

The day might come when you want to Disassemble Mira Shower Head. Maybe you want to strip it because you want to clean it. Maybe you want to disassemble it because you need to replace the spray plate or seals. Or you may want to because of Poor spray pattern from the Cloud spray plate assembly.

Mira shower heads are designed to give a satisfactory shower over a range of pressures. These shower heads are suitable for pressures between 0.1 and 5.0 bar.

Cloud Spray Plate

Cleaning

Accessories

Disassemble Mira Shower Head.

Replacing the Spray plate or Seals.

Replacing the Spray plate or Seals

  1. Use a suitable tool to remove the grommets.
  2. Using the 2.5 mm hexagonal wrench (supplied), remove the screws.
  3. Separate the spray plate assembly into its individual components.
  4. Clean or replace components as necessary.Note! Make sure that the seals are located correctly.
  5. Reassemble the components in reverse order.

 

 

Replacing the Cloud Spray Plate Assembly.

Replacing the Cloud Spray plate Assembly

  1. Use a suitable tool to remove the grommets.
  2. Using the 2.5 mm hexagonal wrench (supplied), remove the screws.
  3. Separate the sprayplate assembly into its individual components.
  4. Replace the Cloud assembly sprayplate with the LC version.
  5. Reassemble the components in reverse order.

 

 

Disassemble Mira Shower Head – Cleaning.

Disassemble Mira Shower Head - Cleaning

Many household cleaners contain abrasives and chemical substances, and should not be used for cleaning plated or plastic fittings.These finishes should be cleaned with a mild washing up detergent or soap solution, and then wiped dry using a soft cloth.Use your thumb or a soft cloth to wipe any limescale from the soft nozzles and the front surface of the shower head spray plate.Important! The spray plate must be regularly cleaned to make sure that the shower head does not become blocked.

Use your thumb or a soft cloth to wipe any limescale from the soft nozzles.

 

 

Accessories.

Flow Regulator (12 L/min – Red) – 1641.059If your shower has no flow control, you may find operation of the shower on high pressure systems too forceful. Fitting a flow regulator in the shower head will reduce this.

Disassemble Mira Shower Head - Flow Regulator

Check valve (360m and 360r) – 1688.282

Mira Shower Head - Check Valve

Check valve (360i) – 1688.283

Mira Shower Head - Checkvalve (360i) - 1688.283

To comply with UK Water Regulations you must make provision to prevent the back flow of waste water through the shower.A hose retaining ring will allow compliance but may restrict full use of the hose.However, if your mixer shower is already fitted with single inlet check valves then fitting the extra shower head check valve will allow compliance without the need for the hose retaining ring.

How to clean a showerhead with vinegar

MIRA SHOWER HEAD INSTALLATION & USER GUIDE

Showerhead

Multifunction showerhead assembly

Showerhead

Shower head assembly